Журналы →  Tsvetnye Metally →  2016 →  №1 →  Назад

Название Layer thickness influence on the Inconel 718 alloy microstructure and properties under selective laser melting
DOI 10.17580/tsm.2016.01.14
Автор Sufiiarov V. Sh., Popovich A. A., Borisov E. V., Polozov I. A.
Информация об авторе

Peter the Great Saint Petersburg Polytechnic University, Saint Petersburg, Russia:

V. Sh. Sufiiarov, Leading Researcher, e-mail: vadim.spbstu@yandex.ru
A. A. Popovich, Professor, Director of the Institute of Metallurgy, Mechanical Engineering and Transport
E. V. Borisov, Post-Graduate Student, Researcher
I. A. Polozov, Student, Engineer


The microstructure and properties of the specimens of the Inconel 718 heatresistant nickel alloy produced by selective laser melting (SLM) were studied. The layer thickness, laser power, laser scanning speed and pass distance impact on the microstructure, porosity and phase composition of a compact specimen were studied. Varying the main technological parameters allowed to determine the values that provide maximum relative density of compact material. The study of microstructure of the obtained specimens allowed to estimate configuration of the solidified molten pools and their mutual arrangement. The height of these pools is more than the thickness of the layer which indicates of the significant remelting of the underlying lauer. The microstructure of the specimens represents directional columnar dendrite cells. The executed study showed distinctions between the initial powder material and compact specimens phase composition. These distinctions are caused by differences between metal cooling during the powder gas atomization and alloy laser treatment by the selective laser melting. There are also shown the distinction between phase compositions at different layer thickness which are the evidences of the alloy crystallisation under different conditions. Mechanical properties of the specimens made according to the selected process parameters were determined. The research allows to establish the influence of the specimens’ layer thickness during manufacturing on their strength and plastic properties. When using a thinner powder layer, strength properties are higher however the plastic ones are lower, compared to material obtained using thicker powder layers. Influence of the position of the samples on a base plate during manufacturing on their strength and plastic properties was also revealed. The horizontally grown samples show higher strength properties and lower ductility than the vertically built specimens.

Ключевые слова Additive manufacturing, selective laser melting, additive technologies, nickel super alloy, powder metallurgy, layer-by-layer laser melting
Библиографический список

1. Chester T. Sims, Norman S. Stoloff, William C. Hagel. Supersplavy II: Zharoprochnye materialy dlya aerokosmicheskikh i energeticheskikh ustanovok (Superalloys II: Heat-resistant materials for aerocosmic and energetic units). Moscow : Metallurgiya, 1995. 385 p.
2. Reed R. C. The Superalloys: Fundamentals and Applications. Cambridge : Cambridge University Press, 2006. 372 p.
3. Zlenko M. A., Popovich A. A., Mutylina I. N. Additivnye tekhnologii v mashinostroenii (Additive technologies in machine-building). Saint Petersburg : Publishing House of Polytechnical University, 2013. 222 p.
4. Yadroitsev I., Smurov I. Selective laser melting technology: from the single laser melted track stability to 3D parts of complex shape. Physics Procedia. 2010. Vol. 5. pp. 551–560.
5. Ma M., Wang Z., Gao M., Zeng X. Layer thickness dependence of performance in high-power selective laser melting of 1Cr18Ni9Ti stainless steel. Journal of Materials Processing Technology. 2015. Vol. 215. pp. 142–150.
6. Yadroitsev I., Yadroitseva I., Bertrand Ph., Smurov I. Factor analysis of selective laser melting process parameters and geometrical characteristics of synthesized single tracks. Rapid Prototyping Journal. 2012. Vol. 18, No. 3. pp. 201–208.
7. Sufiyarov V. Sh., Popovich A. A., Borisov E. V., Polozov I. A. Selektivnoe lazernoe plavlenie zharoprochnogo nikelevogo splava (Selective laser melting of heat-resistant nickel alloy). Tsvetnye Metally = Non-ferrous metals. 2015. No. 1. pp. 79–84. DOI: http://dx.doi.org/10.17580/nfm.2015.01.08
8. Nerush S. V., Evgenov A. G., Ermolaev A. S., Rogalev A. M. Issledovanie melkodispersnogo metallicheskogo poroshka zharoprochnogo splava na nikelevoy osnove dlya lazernoy LMD naplavki (Research of fine-disperse metallic powder of heat-resistant nickel-based alloy for laser LMD buildingup). Voprosy materialovedeniya = Inorganic Materials: Applied Research. 2013. No. 4. pp. 98–107.
9. Libenson G. A., Lopatin V. Yu., Komarnitskiy G. V. Protsessy poroshkovoy metallurgii. Tom 1. Proizvodstvo metallicheskikh poroshkov (Processes of powder metallurgy. Volume 1. Production of metallic powders). Moscow : MISiS, 2001. 368 p.
10. Inconel alloy. 718 Special Metals. Available at: http://www.specialmetals.com/documents/Inconel%20alloy%20718.pdf (accessed: October 11, 2015).
11. GOST 1497–84. Metally. Metody ispytaniy na rastyazhenie (State Standard 1497–84. Metals. Pull test methods). Introduced: January 01, 1986. (in Russian)
12. GOST 25281–82. Metallurgiya poroshkovaya. Metod opredeleniya plotnosti formovok (State Standard 25281–82. Powder metallurgy. Method of determination of formings density). Introduced: January 01, 1983. (in Russian)
13. Averyanova M., Cicala E., Bertrand Ph., Grevey D. Optimization of Selective Laser Melting technology using design of experiments method. Innovative Developments in Virtual and Physical Prototyping : Proceedings of the 5th International Conference on Advanced Research in Virtual and Rapid Prototyping, Leiria, Portugal, 28 September – 1 October, 2011. CRC Press, 2011. pp. 459–466.
14. Holzweissig M. J., Taube A., Brenne F., Schaper M. Microstructural Characterization and Mechanical Performance of Hot Work Tool Steel Processed by Selective Laser Melting. Metallurgical and Materials Transactions B. 2015. Vol. 46, No. 2. pp. 545–549.
15. ASTM F3055. Additive Manufacturing Nickel Alloy (UNS N07718) with Powder Bed Fusion.

Language of full-text русский
Полный текст статьи Получить