Журналы →  Tsvetnye Metally →  2016 →  №1 →  Назад

Название Degassing and modification of aluminum-tin alloys
DOI 10.17580/tsm.2016.01.12
Автор Mironov A. E., Gershman I. S., Kotova E. G.
Информация об авторе

Railway Research Institute, Moscow, Russia:

A. E. Mironov, Leading Researcher
I. S. Gershman, Head of Laboratory of Non-Ferrous Metals and Tribology, e-mail: isgershman@gmail.com
E. G. Kotova, Post-Graduate Student


There was made a comparison of the impact of degassing and modifying properties of various reagents on the properties and structure of the cast antifriction aluminum-tin alloys. As of now, most of the aluminum-tin alloys are used as a sliding layer of the double-layer slider bearings. The design of such bearings represents a rugged steel case joint by rolled anti-friction material. The first step in obtaining the molding material is casting. The cast anti-friction aluminum-tin alloys are working out as a replacement of anti-friction bronzes in the shaft-bearing friction nodes. Cast bearings can be broken not only in result of wear, but of fatigue damages as well. In this connection, mechanical properties of alloys for bearing are important no less than the anti-friction ones. Not only composition of alloys affect their mechanical properties, but melting and cast technologies as well. Impact of these technological operations on chemical composition, microstructure and alloy properties is demonstrated. It has been revealed an advantage of a Zernolit-2 (Зернолит-2) degasser and modifier over preparations of the Schafer company. It is noted that use of degassers and modifiers allows to improve mechanical properties and hot-shortness of cast anti-friction aluminum-tin alloys. It is demonstrated that the Zernolit-2 degasser and modifier guarantees much more durability and plasticity and less hot-shortness of the alloy than the Schafer preparations do. Using Zernolit-2 degasser and modifier provides heightened slag formation which means that it surpasses Schafer preparations in the alloy cleaning of impurities. Mechanisms of degassing and modifying influence upon the properties and structure of alloy are discussed. It is pointed out that significant size reduction of aluminum grains and the soft structural component inclusions additionally increase mechanical properties of the cast anti-friction aluminum-tin alloys when using modifiers and degassers.

Ключевые слова Aluminum-tin alloys, degassing, modification, grain size, structure, hot-shortness, mechanical properties, slag formation
Библиографический список

1. Bushe N. A. et al. Podshipniki iz alyuminievykh splavov (Aluminium alloy bearings). Moscow : Transport, 1974. 256 p.
2. Zhu M., Zeng M. Q., Gao Y., Ouyang L. Z., Li B. L. Microstructure and wear properties of Al – Pb – Cu alloys prepared by mechanical alloying. Wear. 2002. Vol. 253, No. 7/8. pp. 832–838.
3. An J. Microstructure and tribological properties of Al – Pb alloy modified by high current pulsed electron beam. Wear. 2006. Vol. 261, No. 2. pp. 208–215.
4. Liu X., Zeng M. Q., Ma Y., Zhu M. Wear behavior of Al–Sn alloys with different distribution of Sn dispersoids manipulated by mechanical alloying and sintering. Wear. 2008. Vol. 265, No. 11/12. pp. 1857–1863.
5. Anila M., Srivastavab V. C., Ghosha M. K., Ojha S. N. Influence of tin content on tribological characteristics of spray formed Al – Si alloys. Wear. 2010. Vol. 268, No. 11/12. pp. 1250–1256.
6. Kim Il-Young, Lee Jung-Hee, Lee Gyu-Sun, Baik Seung-Hyun, Kim Young-Jig, Lee Young-Ze. Friction and wear characteristics of the carbon nanotube–aluminum composites with different manufacturing conditions. Wear. 2009. Vol. 267, No. 1–4. pp. 593–598.
7. Kotova E. G., Kurbatkin I. I., Mironov A. E., Gershman I. S. Issledovanie mikrostruktury i mekhanicheskikh svoystv eksperimentalnykh antifriktsionnykh splavov (dlya monometallicheskikh podshipnikov skolzheniya) (Research of microstructure and mechanical properties of experimental antifriction alloys (for monometallic slide bearings)). Tsvetnye Metally = Non-ferrous metals. 2013. No. 5. pp. 66–71.
8. Abd El-Salam F., Abd El-Khalek A. M., Nada R. H., Wahab L. A., Zahran N. Y. Effect of Sn content on structural and mechanical properties of Al – Si alloy. Mater Science and Engineering: A. 2010. Vol. 527. pp. 1223–1229.
9. Prasada Rao A. K. Nucleation in Al Alloys Processed by MCDC Casting. Journal of Materials Engineering and Performance. 2015. Vol. 24, No. 6. pp. 2219–2224.
10. Gorny M., Sikora G. Effect of Titanium Addition and Cooling on Primary a (Al) Grains and Tensile Properties of Al – Cu Alloy. Journal of Materials Engineering and Performance. 2015. Vol. 24, No. 3. pp. 1150–1156.
11. Mondolfo L. F. Struktura i svoystva alyuminievykh splavov (Structure and properties of aluminiunm alloys). Moscow : Metallurgiya, 1979. 639 p.
12. Fras E., Wiencek K., Gorny M., Lopez H. F. et. al. Equiaxed Grain Count in Aluminium Alloy Castings: Theoretical Background and Experimental Verification. Metallurgical and Materials Transactions A. 2013. Vol. 44, No. 13. pp. 5788–5795.
13. Novikov I. I. Goryachelomkost tsvetnykh metallov i splavov (Hot-shortness of non-ferrous metals and alloys). Moscow : Nauka, 1966. 299 p.
14. Sweet L., Easton M. A., Taylor J. A., Grandfield J. F. et. al. Hot Tear Susceptibility of Al – Mg – Si – Fe Alloys with Varieng Iron Contents. Metallurgical and Materials Transactions A. 2013. Vol. 44, No. 12. pp. 5396–5407.
15. GOST 14113–78. Splavy alyuminievye antifriktsionnye. Marki (State Standard 14113–78. Aluminium antifriction alloys. Grades). Introduced: January 01, 1980. (in Russian).

Language of full-text русский
Полный текст статьи Получить