Журналы →  Tsvetnye Metally →  2022 →  №11 →  Назад

MATERIALS SCIENCE
Название Сontinuous walking beam furnace without water cooling for reheating copper alloy blanks
DOI 10.17580/tsm.2022.11.07
Автор Kazyaev M. D., Kazyaev D. M., Kiselev E. V., Vokhmyakov A. M.
Информация об авторе

M. D. Kazyaev (1934–2022)

 

UralTermoKompleks Research & Production Company, Yekaterinburg, Russia:

D. M. Kazyaev, Director, e-mail: termokomplex@r66.ru
A. M. Vokhmyakov, Chief Engineer, Candidate of Technical Science, e-mail: vam@termokomplex.ru

Ural Federal University named after the First President of Russia B. N. Yeltsin, Yekaterinburg, Russia:

E. V. Kiselev, Associate Professor at the Department of Thermal Physics and Computer Science in Metallurgy, Candidate of Technical Science, e-mail: ev.kiselev@urfu.ru

Реферат

It takes a special technique to heat up round blanks cast of copper alloys in conformance with applicable process specification, which implies maintaining a low oxidizing atmosphere in a gas furnace. This paper describes a continuous furnace with walking beams that are not watercooled designed to heat up round blanks to the maximum temperature of 1,000 ºC. The furnace, which stands before the pipe press for making pipes of different sizes, is fueled by natural gas burned in high-speed burners with the air flow rate of α = 0.98 in hot zones and that of α = 1.05–1.1 in preheating zones. The side walls of the furnace are equipped with high-speed burners which serve to intensify the convective heat transfer inside the furnace. The burners ensure a transverse/countercurrent flow of gases with an intense transverse jet circulation. The furnace is equipped with a panel roof lined with ribbed ceramic fiber blocks (original design by UralTermoKompleks) which serves to intensify the radiation heat transfer without raising the temperature. A larger interior surface of the furnace roof leads to an increased radiation heat flow density and hence higher heating rates. It means that the furnace has better performance at the same temperature. The furnace is equipped with charging and discharging systems. An eccentric is responsible for moving the walking beams. An integrated control system controls heat in each of the five zones of the furnace guided by thermocouples and charging and discharging modes. The furnace has been fully commissioned.

Ключевые слова Continuous furnace, walking beams without water cooling, heating, round blanks, copper alloys, burners, natural gas, different air flow rate in furnace zones
Библиографический список

1. Gusovskiy V. L., Livshits A. E., Usachev A. B. Reheating and heat-treatment furnaces of Stalproekt. Moscow : Alteks, 2015. 283 p.
2. Gusovskiy V. L., Ladygichev M. G., Usachev A. B. Modern reheating and heat-treatment furnaces. Handbook. Moscow : Teplotekhnik, 2007. 656 p.
3. Vokhmyakov A. M., Kazyaev M. D., Arseev B. N., Kazyaev D. M. The quality of reheating copper slabs when operating fuel burners in pulsed mode. Conference proceedings. Yekaterinburg : UGTU-UPI, 2010. pp. 74–82.
4. Spitchenko D. I., Vokhmyakov A. M., Kazyaev M. D., Kiselev E. V., Kazyaev D. M. Continuous walking beam furnace for heating of copper and copper-alloy ingots. Tsvetnye Metally. 2014. No. 10. pp. 83–87.
5. Gushchin S. N., Ageev N. G., Kryuchenkov Yu. V. Fundamentals of energy technology processes used in non-ferrous metallurgy : textbook for university students. Ed. by Yu. G. Yaroshenko. Yekaterinburg : UGTU-UPI, 2000. 312 p.
6. Pugacheva N. B., Ovchinnikov A. S., Lebed A. V. Analysis of defects of industrial brass blanks. Tsvetnye Metally. 2014. No. 10. pp. 71–87.
7. Smirnov S. V., Pugacheva N. B., Soloshenko A. N., Tropotov A. V. Understanding the plastic deformation of complex alloyed brass. Fizika metallov i metallovedenie. 2002. Vol. 93, No. 6. pp. 91–100.
8. Hasan Ajili S., Haratian M., Karimipour A., Bach Q.-V. Non-uniform slab heating pattern in a preheating furnace to reduce fuel consumption: burners’ load distribution effects through semitransparent medium via discreet ordinates’ thermal radiation and k– turbulent model. International Journal of Thermophysics. 2020. Vol. 41, Iss. 9. p. 128.
9. Kazyaev M. D., Kazyaev D. M., Vokhmyakov A. M. Modern energy-saving techniques for reheating furnaces. New Trends in the Field of Heat Engineering: 4th International congress. Moscow, 2015. pp. 40–60.
10. Liu Y., Wang J., Min C., Xie G., Sundén B. Performance of fuel-air combustion in a reheating furnace at different flowrate and inlet conditions. Energy. 2020. Vol. 206. p. 118206.
11. Kashcheev I. D. The properties and application of refractories. Moscow : Teplotekhnik, 2004. 352 p.
12. Li C., Huang Y., Sun J., Ni Y., Lu L. Numerical simulation of pressure distribution in a walking-beam type reheating furnace. IOP Conference Series: Earth and Environmental Science. 2020. Vol. 467, Iss. 1. p. 012025.
13. Jang J.-Y., Huang J.-B. Optimisation of a slab heating pattern with various skid button heights in a walking-beam-type reheating furnace. Ironmaking and Steelmaking. 2018. Vol. 45, Iss. 9. pp. 793–804.
14. Lin C.-N., Luo Y.-P., Jang J.-Y., Wang C.-H. Novel approach to estimate the optimum zone fuel mass flow rates for a walking beam type reheating furnace. Heat Transfer Engineering. 2018. Vol. 39, Iss. 7-8. pp. 586–597.

Language of full-text русский
Полный текст статьи Получить
Назад