Журналы →  Chernye Metally →  2022 →  №10 →  Назад

Foundry Production
Название Investigation of the effect of thermal-oxidative destruction of pyrocarbon on formation of structure of a binder and residual strength of sand-liquid-glass mixtures
DOI 10.17580/chm.2022.10.06
Автор N. A. Kidalov, N. V. Grigoryeva, A. A. Belov, N. I. Gabelchenko
Информация об авторе

Volgograd State Technical University, Volgograd, Russia:

N. A. Kidalov, Dr. Eng., Prof., Head of the Dept. of Machinery and Technology of Foundry
N. V. Grigoryeva, Lecturer of the Dept. of Machinery and Technology of Foundry
A. A. Belov, Cand. Eng., Lecturer of the Dept. of Machinery and Technology of Foundry, e-mail: aa-belov@bk.ru
N. I. Gabelchenko, Cand. Eng., Associate Prof. of the Dept. of Machinery and Technology of Foundry

Реферат

A study of the effect of thermal-oxidative degradation of a carbon-containing additive on the formation of the binder film structure and the residual strength of sand-liquidglass mixtures after various calcination temperatures is presented. Pyrolyzed industrial carbon (pyrocarbon) of P324 grade was used as an additive. The methods of differential thermal and thermogravimetric analyzes were used to study the physical and chemical processes that occur with the investigated carbon-containing material when heated to a temperature characteristic of the heating of the surface layer of the core (molding) mixture in contact with liquid steel. This made it possible to reveal the temperature ranges of the degradation of the carbon-containing additive, which lead to a violation of the integrity of the sodium silicate film and a decrease in the residual strength of the sand-liquid-glass mixture. For a comparative analysis of the structure of silicate binder films and the residual strength of sand-liquid-glass mixtures after calcination at temperatures of 453, 673, 873, and 1073 K (180, 400, 600, and 800 °C), standard cylindrical samples from reference (quartz sand of 1K2O303 grade and liquid glass with a silicate modulus of 2.8, a density of 1490 kg/m3 as a binder) and experimental (with the introduction of pyrolytic carbon in the amount of 2 % (wt.)) mixtures have been prepared. As a result of the study, it was found that the residual strength of the studied sand-liquid-glass mixtures depends on the morphological features of the surface of the silicate binder film, expressed by the presence of carbonaceous formations (soot), pores and crystals of sodium carbonates (stress concentrators in the binder film).

Ключевые слова Sodium silicate aqueous solution, sand-liquid-glass mixture, carbon-containing additive, sodium carbonate crystals, porosity, residual strength
Библиографический список

1. Tkachenko S. S., Kolodiy G. А., Znamenskiy L. G., Ermolenko А. А. About highly efficient and environmentally friendly foundry technology. Chernye Metally. 2019. No. 2. pp. 25–29.
2. Illarionov I. Е. Application of fabrication technology for metal phosphate binders, core sands and moulding mixtures on their base. Chernye Metally. 2018. No. 4. pp. 13–19.
3. Lyass А. М. Quick-setting molding sands. Moscow: Mashinostroenie, 1965. 332 p.
4. Zhukovskiy S. S., Boldin А. N. Foundry technology: molding and core sands. Bryansk: BGTU, 2002. 470 p.
5. Stechman M., Rözycka D., Baliński A. Modification of aqueous sodium silicate solutions with morphoactive agents. Journal of Chemical Technology. 2003. Vol. 5. pp. 47.
6. Ryu Y. B., Lee M. S. Infrared spectra and thermal properties of sodium silicate solutions. Journal of Korean Institute of Metals and Materials. 2018. Vol. 56. pp. 72–78.
7. Stachowicz M. Modified hot distortion test to investigate the effect of the inorganic binder on the high-temperature behaviour of physically hardened moulding sands. Archives of Foundry Engineering. 2018. Vol. 18. pp. 45–50.
8. Major-Gabrys K., Grabarczyk A., Dobosz M. Modification of foundry binders by biodegradable material. Archives of Foundry Engineering. 2018. Vol. 18. pp. 31–34.
9. Kidalov N. A., Adamova A. S., Grigoreva N. V. Selection of technological additives to the composition of the moulding mixtures based on water glass. International Journal of Cast Metals Research. 2021. Vol. 34, Iss. 3–6. pp. 162–168.
10. Zhao Li. Y., Du J., Sun X., Song Y., Miao G. The optimization of the properties of sodium silicate bonded ceramic sand by nano-oxide particles and ultrasonication. International Journal of Metalcasting. 2022. Vol. 16. pp. 234–241.
11. Miao H., Sun Du. X., Zhang Y., Song M. G. Effect of powder breakdown additives on properties of ester-hardened sodium silicate bonded ceramic sand. International Journal of Metalcasting. 2021. Vol. 15. pp. 710–718.
12. Jung Y., Tumenbayar E., Choi H., Park H., Kim E., Zhang J. Effects of alumina precursor species in a ternary-phase binder system on the strength of sand mold. Ceramics International. 2018. Vol. 44. pp. 2223–2230.
13. Al-Saraireh F. M. An assessment of the efficiency of utilizing complex modifiers for softening the liquid-glass mixtures to improve iron and steel casting. ARPN Journal of Engineering and Applied Sciences. 2018. pp. 3231–3235.
14. Leushin I. O., Leushina L. I., Balabanov I. P., Savin I. A. Production of moulding cores and waterglass mixtures using "dry ice" for steel and iron casting. CIS Iron and Steel Review. 2021. Vol. 21. pp. 34–37.
15. Leushin I. О., Koshelev О. S., Maslov К. А., Titov А. V. Evaluation of the use of softening additives in the practice of production of foundry cores. Vestnik Magnitogorskogo gosudarstvennogo tekhnicheskogo universiteta imeni G. I. Nosova. 2020. Vol. 18. No. 3. pp. 25–33.
16. GOST 21 38–91. Moulding sands. General specifications. Introduced: 01.01.1993. Moscow: Izdatelstvo standartov, 1986. 8 p.
17. GOST 13078–2021. Sodium silicate solute. Specifications. Introduced: 01.05.2022. Moscow: FGBU "RST", 2021. 19 p.
18. GOST 7885–86. Carbon black for rubber industry. Specifications. Introduced: 01.01.1988. Moscow: Izdatelstvo standartov, 1997. 16 p.
19. GOST 29234.11–91. Moulding sands. Method for determination of gas permeability. Introduced: 01.01.1993. Moscow: Izdatelstvo standartov, 1992. 4 p.
20. GOST 23409.7–78. Moulding sands, moulding and core sand mixtures. Methods for determination of compressive, tensile, bending and shearing strength. Introduced: 01.01.1980. Moscow: Izdatelstvo standartov, 1985. 6 p.
21. Vereshchagin V. I., Borilo L. P., Kozik А. V. Physical and chemical study of porous composite SiO2 materials. Khimiya i khimicheskaya tekhnologiya. 2003. Vol. 46. No. 8. pp. 138–140.

Language of full-text русский
Полный текст статьи Получить
Назад