Journals →  Tsvetnye Metally →  2024 →  #2 →  Back

COMPOSITES AND MULTIPURPOSE COATINGS
ArticleName Effect of wear-resistant nACo coating on the properties of 6WH10F hard alloy
DOI 10.17580/tsm.2024.02.11
ArticleAuthor Kozik E. S., Svidenko E. V.
ArticleAuthorData

Orenburg State University, Orenburg, Russia

E. S. Kozik, Associate Professor at the Department of Descriptive Geometry, Engineering and Computer Graphics, Candidate of Technical Sciences, e-mail: ele57670823@yandex.ru
E. V. Svidenko, Associate Professor at the Department of Materials Science and Materials Engineering, Candidate of Technical Sciences, e-mail: tzvetkova.katia2016@yandex.ru

Abstract

A modern approach to enhancing the performance of cutting tools involves the use of various techniques for applying wear-resistant coatings to the tool surface. Such choice comes down to the fact that this layer ensures high wear resistance of the item whereas the host material acts as a carrier. The authors of this paper applied a wear-resistant nACo coating to hard alloy of 6WH10F grade. Pillar-shaped specimens of 6WH10F hard alloy with the diameter of 10 mm and the height of 10 mm were used for the study. A nACo(Ti, Al)N coating was applied to them in a PLATIT unit at 550 oC. The Physical Vapour Deposition (PVD) technique was applied with plasma generation, while also using the conventional ARC cathode technique (PL 70, PL1001, PL 2001). Coatings with pre-defined thicknesses of 2 to 3 μm were applied to all items. This allowed to obtain a batch of items with homogenous coatings and ensure a high reproducibility of the coating quality. The layers were applied evenly, the absence of shells or cracks being an indicator of good adhesion. The authors determined the boundary between the coa ting applied and the substrate, as well as the coating thickness. With the help of a JEOL electron microscope operated in automatic mode, the concentration of chemical elements was analyzed in the deposited layer — i. e. in the outer and intermediate layer (an intermediate layer between the coating and the hard alloy). Due to this, the presence of the following elements was identified based on pre-defined identifications: N, C, B, O, Al, Si, P, S, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Zr, Nb, Mo, Ag, W, Au. To determine the performance of specimens with coatings and without them, they were tested for diamond-abrasive wear in a special unit, with the test durations of 3, 6 and 9 minutes. The technique implies rubbing specimens against a diamond cup (‘АСЧ 100×90 С22 4 82-01’) per GOST 17367–71, with the load of 1 N applied to 1 mm2 of the specimen area. The mass wear, wear intensity and rate, as well as wear resistance were also calculated. The authors would like to thank A.A. Stepanov for preparation of and deposition of coatings to specimens.

keywords 6WH10F grade hard alloys, nACo coating, microstructure, surface layer, chemical elements, point analysis.
References

1. Kreymer G. S. Strength of hard alloys. Moscow : Metallurgiya, 1971. 247 p.
2. Panov V. S., Chuvilin A. M. Technology and properties of sintered hard alloys and items made of them. Moscow : MISiS, 2001. 428 p.
3. Suzuki H., Hayashi K. Strenght of WC – Co cemented carbides in relation to their fracture sources. Planseeber. Pulverment. 1975. Vol. 23, No. 1. pp. 24–36.
4. Zhang Li., Wang Yuan-jie., Yu Xian-wang., Chen Shu. et al. Crack propagation characteristic and toughness of functionally graded WC – CO cemented carbide. International Journal of Refractory Metals and Hard Materials. 2020. Vol. 26, No. 4. pp. 295–300.
5. Colovcan V. T. Some analytical consequences of experiment data on properties of WC – Co hard metals. International Journal of Refractory Metals and Hard Materials. 2021. Vol. 26, No. 4. pp. 301–305.
6. Guo Zhixing, Xiong Ji, Yang Mei, Jiang Cijin. WC – TiC – Ni cemented carbide with enhanced properties. Journal of Alloys and Compounds. 2020. Vol. 465, No. 1–2. pp. 157–162.
7. Gurland J. The fracture strength of sintered WC-Co alloys in relation to composition and particle spacing. Transactions of the Metallurgical Society of AIME. 1963. Vol. 227, No. 1. pp. 28–43.
8. Bondarenko V. A., Bogodukhov S. I. Ensuring the quality and enhancing the characteristics of cutting tools. Moscow : Mashinostroenie, 2000. 128 p.
9. Sokolov A. G. Method of hard-alloy tool machining. Patent RF, No. 2509173. Applied: 12.02.2003. Published: 10.03.2014.
10. Bogodukhov S. I., Kozik E. S., Svidenko E. V. Hard alloys hardening method. Patent RF, No. 2693238. Applied: 18.10.2018. Published: 01.07.2019.
11. Kim C. S., Massa T. P., Rohrer G. S. Modeling the relationship between microstructural features and the strengh of WC – Co composites. International Journal of Refractory Metals and Hard Materials. 2020. Vol. 24, Iss. 1. pp. 89–100.
12. Yamamoto T., Ikuhara Y., Watanabe T. et al. High resolution microscopy study in Cr3C2-doped WC – Co. Journal of Materials Science. 2001. No. 36. pp. 3885–3890.
13. Khindrik E. Cutting tool insert for steels turning. Patent RF, No. 2536014. Applied: 10.09.2013. Published: 20.12.2014.
14. GOST 17367–71. Metals. Method of abrasion test by friction against embedded abradant grain. Introduced: 01.01.1973.

Language of full-text russian
Full content Buy
Back