Journals →  Tsvetnye Metally →  2024 →  #1 →  Back

METAL PROCESSING
ArticleName Effect of shell ceramic mould temperature before pouring and that of pouring temperature on defects forming in cast combustion chamber body made of nickel superalloy VZhL14N-VI
DOI 10.17580/tsm.2024.01.10
ArticleAuthor Nikitina A. A., Bazhenov V. E., Koltygin A. V., Belov V. D.
ArticleAuthorData

National University of Science and Technology MISIS, Moscow, Russia.

A. A. Nikitina, Assistant at the Department of Casting and Material Working, e-mail: nikitina.misis@gmail.com
V. E. Bazhenov, Associate Professor at the Department of Casting and Material Working, Candidate of Technical Sciences, e-mail: v.e.bagenov@gmail.com
A. V. Koltygin, Associate Professor at the Department of Casting and Material Working, Candidate of Technical Sciences, e-mail: misistlp@mail.ru
V. D. Belov, Head of the Department of Casting and Material Working, Doctor of Technical Sciences, e-mail: vdbelov@mail.ru

Abstract

Stability of process parameters is essential for obtaining good quality castings. Even that the ranges of permissible values of such parameters as casting and mould temperature or transfer time are quite wide, the final castings belonging to different batches may have differing quality. This paper analyzes some temperature-time parameters of the investment casting process to make cast bodies. The effect of the above mentioned parameters on the product quality was established. For this, computer simulation was carried out for the pouring and solidification of large thin-wall castings of nickel superalloy VZhL14N-VI cast in shell ceramic moulds. The simulation data show that a criterion for judging the quality of a casting includes the volume of shrinkage porosity in the casting. The authors analyzed a combined effect of the simulation parameters on the cooling rate of the casting wall. Thus, the authors give a number of recommendations on casting process optimization for obtaining castings as per specification. It was found that the difference between the pouring temperature and the mould temperature that ensured the casting cooling rate in the alloy freezing range of at least 2 oC/sec had translated into the best quality castings. Any further increase in the casting cooling rate does not influence the porosity.
This research was funded by the Ministry of Science and Higher Education of the Russian Federation following Governmental Decree No. 218 under Subsidy Agreement No. 075-11-2022-023 dated 6 April 2022: Developing a Process for Making Unique Large Superalloy Castings for Gas Turbine Engines with the Focus on Using Domestically Made Equipment and Setting Up Modern, Sustainable and Computer-Oriented Foundries.

keywords Nickel superalloys, pouring temperature, shrinkage defects, gas turbine engines, simulation of casting processes, investment casting
References

1. Rakhmankulov M. M., Parashchenko V. M. Casting of heat-resistant alloys. Moscow : Intermet Inzhiniring, 2000. 464 p.
2. Campbell J. Castings principles: the new metallurgy of cast metals. 2nd ed. Burdlington, Mass : Butterworth Heinemann, 2003. 352 p.
3. Beeley P. R. Foundry technology. 2nd, ed. Oxford ; Boston : Butterworth Heinemann, 2001. 719 p.
4. Sun B., Wang J., Shu D. Precision forming technology of large superalloy castings for aircraft engines. Springer Nature Singapore, 2021. 410 p.
5. Pattnaik S., Karunakar D. B., Jha P. K. Developments in investment casting process — A review. Journal of Materials Processing Technology. 2012. Vol. 212, Iss. 11. pp. 2332–2348.
6. Ransing R. S., Sood M. P. Optimization in castings — An overview of relevant computational technologies and future challenges. Metallurgical and Materials Transactions B. 2006. Vol. 37, Iss. 6. pp. 905–911.
7. Rassokhina L. I., Bityutskaya O. N., Gamazina M. V., Echin A. B. Adopting the process of casting parts of Diffuzor gas turbine engines out of VZh159 alloy at a machine-building facility. Trudy VIAM. 2019. No. 12(84). pp. 20–28.
8. Stefanescu D. M. Computer simulation of shrinkage related defects in metal castings – a review. International Journal of Cast Metals Research. 2005. Vol. 18, Iss. 3. pp. 129–143.
9. Antsiferov P. V., Belyakov N. N., Oborin L. A. Mathematical modelling as one of the efficient mechanisms of shaping castings. Aktualnye problemy aviatsii i kosmonavtiki. 2018. Vol. 1, No. 14. pp. 404–405.
10. Yu J.,Wang D., Li D, Tang D. et al. Engineering computing and datadri ven for gating system design in investment casting. International Journal of Advanced Manufacturing Technology. 2020. Vol. 111, Iss. 3-4. pp. 829–837.
11. Prashanth Yadav A., Reddy G. S., Hafeez Md. Modeling and simulation of investment casting to minimize shrinkage porosity in boom post. AIP Conference Proceedings. 2021. Vol. 2358, Iss. 1. 100022.
12. Dubrovskaya A. S., Dongauzer K. A., Trufanov N. A. Mathematical modelling of the casting process to make gas turbine engine parts. Izvestiya Samarskogo nauchnogo Tsentra Rossiyskoy Akademii Nauk. 2012. Vol. 14, No. 4. pp. 1368–1371.
13. Anglada E., Meléndez A., Maestro L., Dominguez I. Adjustment of numerical simulation model to the investment casting process. Procedia Engineering. 2013. Vol. 63. pp. 75–83.
14. Nikulin I. L. Mathematical modelling of the temperature fields in a shell mould before pouring. Perm National Research Polytechnic University Bulletin. Applied Mathematics and Mechanics. 2013. No. 11. pp. 69–79.
15. Tao P., Shao H., Ji Z., Nan H. et al. Numerical simulation for the investment casting process of a large-size titanium alloy thin-wall casing. Progress in Natural Science: Materials International. 2018. Vol. 28. pp. 520–528.
16. Zarifzhonov Zh. F., Pryagaev V. M. A comparative analysis of computer programmes for casting process simulation. Innovative Ideas of Young Researchers: Research papers from the proceedings of the 6th International Conference. Ufa, 12 October 2021. Ufa : OOO “Nauchno-izdatelskiy tsentr “Vestnik nauki”, 2021. pp. 53–58.
17. Bazhenov V. E., Koltygin A. V., Nikitina A. A., Belov V. D. et al. Efficiency of concurrent computations in casting process simulation systems. Izvestiya vuzov. Tsvetnaya metallurgiya. 2023. Vol. 29, No. 3. pp. 38–53.
18. OST 1-90126–85. Vacuum melted cast superalloys. Introduced: 01.04.1986.
19. Konrad C. H., Brunner M., Kyrgyzbaev K., Vokl R. et al. Determination of heat transfer coefficient and ceramic mold material parameters for alloy IN738LC investment castings. Journal of Materials Processing Technology. 2011. Vol. 211, Iss. 2. pp. 181–186.
20. Jin H., Li J., Pan D. Application of inverse method to estimation of boundary conditions during investment casting simulation. Acta Metallurgica Sinica (English Letters). 2009. Vol. 22, Iss. 6. pp. 429–434.
21. Flemings M. C. Solidification processing. New York : McGraw Hill, 1974. 420 p.
22. Pikunov M. V. Melting of metals. Crystallization of alloys. Solidification of castings: A guide for university students. Moscow : MISIS, 2005. 414 p.

Language of full-text russian
Full content Buy
Back