Журналы →  Chernye Metally →  2020 →  №4 →  Назад

Название Steel selection and optimization of plug heat treatment for piercing seamless pipes
Автор G. A. Gevorgyan, R. A. Vorobyev, G. V. Pachurin, A. N. Kuzmin
Информация об авторе

Nizhnyi Novgorod State Technical University (Nizhnyi Novgorod, Russia):

G. A. Gevorgyan, Graduate Student, E-mail: borecgor77777@gmail.com
R. A. Vorobiev, Cand. Eng., Associate Prof., E-mail: linuxjuicy@gmail.com
G. V. Pachurin, Dr. Eng., Prof., E-mail: pachuringv@mail.ru
A. N. Kuzmin, Assistant, E-mail: kuznntu@mail.ru


In the manufacture of seamless pipes, the center of a round billet heated to a certain temperature is pierced in a mill and a tube billet is obtained in the form of a hollow shell. The main tool for piercing a hole in a tube stock is the plug mounted on the front of the shaft. The temperature of piercing is approximately 1200 °C. Plugs of the same diameter can be used repeatedly in the piercing mill. During operation, in addition to high temperatures, the plug experiences significant contact pressures, which significantly reduce the service life of the tool. Uninterrupted operation of pipe production can be ensured by maintaining a large stock of plugs. To increase the service life, the surface of the plugs is often subjected to thermal oxidation, which gives it anticorrosive and lubricating properties, which, in turn, prevent, during piercing, welding of the plug surface with the tube cavity. The main consumers of high-strength seamless pipes are the oil and gas industries, and defense industry. Therefore, the issues of increasing the efficiency of piercing production, strength and durability of the tool, ensuring the uninterrupted production of seamless pipes are very relevant. The rationale for the choice of steel grade and the results of development of the optimal technology for the manufacture of plugs for piercing and cross-helical rolling of seamless pipes are presented. Based on the comparison of structural and mechanical characteristics of 4Kh5MF1S, 4Kh5V2FS and 5KhNM steels, the grade of 4Kh5MF1S steel was selected for production of plugs, which provides the optimal quality/price combination. The analysis of the structure and mechanical properties made it possible to recommend the 4Kh5MF1S steel processing mode: quenching from 1070 °C in oil + tempering (holding in oil for 2 hours at a temperature of 600 °C). The 4Kh5MF1S steel treated in this mode can be used for metal products with the increased service life such as the plug with yield strength of σ0.2 = 1448 MPa and strength σ0 = 1705 MPa.

Ключевые слова Alloy steels, rolling production, plugs, seamless pipes, heat treatment, structure, mechanical properties
Библиографический список

1. Pachurin G. V., Vlasov V. A. Mechanical properties of sheet structural steels at operating temperatures. Metal Science and Heat Treatment. 2014. Vol. 56. No. 3-4. pp. 219–223.
2. Filippov А. А., Pachurin G. V., Kuzmin N. А., Matveev Yu. I., Deev V. B. Quality assessment of rolled steel for cold forming. Izvestiya vysshikh uchebnykh zavedeny. Chernaya metallurgiya. 2018. Vol. 61. No. 7. pp. 551–556.
3. Pachurin G. V., Shevchenko S. M., Mukhina M. V., Kutepova L. I., Smirnova J. V. The Factor of Structure and Mechanical Properties in the Production of Critical Fixing Hardware 38XA. Tribology in Industry. 2016. Vol. 38. No. 3. pp. 385–391.
4. Filippov A. A., Pachurin G. V., Naumov V. I., Kuzmin N. A. Low-Cost Treatment of Rolled Products Used to Make Long High-Strength Bolts. Metallurgist. 2016. Vol. 59. No. 9-10. pp. 810–817.
5. Bogdanova Т. А., Pereboeva А. А., Tretyakova L. P., Okladnikova N. V. Study of the structure and properties of stamped tool steels. Vestnik Sibirskogo gosudarstvennogo aerokosmicheskogo universiteta imeni akademika M. F. Reshetneva. 2018. No. 2. pp. 239–241.

6. Fedulov V. N. Ways to increase the durability of a high-loaded tool for hot upsetting of bolts heads. Lityo i metallurgiya. 2016. No. 1. pp. 120–129.
7. Aborkin A. V., Vaganov V. E., Shlegel’ A. N., Bukarev I. M. Effect of Laser Hardening on Die Steel Microhardness and Surface Quality. Metallurgist. 2015. Vol. 59, Iss. 7-8. pp. 619–625.
8. Aborkin A. V., Vaganov V. E., Klimov N. S., Kovalenko D. V., Sobolkov A. V. Treatment with a High-Temperature Pulsed Plasma and Laser Radiation for Die Steel Surface Layer Hardening. Metallurgist. 2016. Vol. 60, Iss. 7-8. pp. 739–744.
9. Fedulov V. N. Optimization of the hardening temperature mode to increase heat resistance of tool steel 4Kh5MF1S in various workpieces. Part 1. Effect of the heating temperature of 1040 °C during quenching in oil and tempering on hardness and structure of forgings and castings from 4Kh5MF1S steel. Lityo i metallurgiya. 2017. No. 2. pp. 97–103.
10. Poznyak L. А., Skrynchenko Yu. М., Tishaev S. I. Stamp steel. Moscow: Metallurgiya, 1980. 150 p.
11. Piercing of a billet in a cross-helical rolling mill. Catalog of industrial enterprises. [electronic resource] Available at: http://www.zawod.ru/info/trubi/bezshovnie-proshivka-poperechnaya.html (accessed: 11.03.2020).
12. Kutepov V. А. The practice of using piercing mill plugs with internal water cooling. Innovative technologies in metallurgy and mechanical engineering: Proceedings of the International youth scientific conference “Innovative technologies in metallurgy and mechanical engineering” dedicated to the memory of the corresponding member of the RAS, Honorary Doctor of UrFU V. L. Kolmogorov. (Ekaterinburg, 26–30 November 2013). Yekaterinburg: Izdatelstvo Uralskogo universiteta, 2014. pp. 427–435.
13. Geller Yu. А. Tool steels. 5th edition. Moscow: Metallurgiya, 1983. 568 p.
14. Fedulov V. N. The eff ect of cooling conditions and the size of a billet during tool steel casting on the ability to subsequent thermal hardening of the surface. Lityo i metallurgiya. 2016. No. 3. pp. 117–127.
15. Guryev А. М., Kharaev Yu. P., Kolyadin А. А., Shametkin О. V. Cast dies for hot volumetric deformation and features of their thermal and chemical-thermal treatment. Liteynoe proizvodstvo. 2004. No. 1. pp. 8–11.
16. GOST 1497–84. Metals. Methods of tension test. Introduced: 01.01.1986.
17. GOST 9454–78. Metals. Methods for testing the impact strength at low, room and high temperature. Introduced: 01.01.1979.
18. Gulyaev А. P. Metal science. Moscow: Metallurgiya, 1986. 544 p.

Language of full-text русский
Полный текст статьи Получить