Journals →  Chernye Metally →  2019 →  #9 →  Back

Tubemaking
ArticleName Features of metal stresses-strained state in hot extrusion of steel pipes
ArticleAuthor A. V. Vydrin, A. S. Zhukov, E. V. Khramkov, M. A. Pavlova
ArticleAuthorData

All-Russian Scientific and Research Institute of Tube Industry — RosNITI (Chelyabinsk, Russia):

A. V. Vydrin, Dr. Eng., Prof., Deputy General Director on Scientific Work, e-mail: vydrinav@rosniti.ru
E. V. Khramkov, Cand. Eng., Head of the labor for simulation of technological processes
M. A. Pavlova, Senior engineer, the labor for simulation of technological processes

 

Volzhsky Pipe Plant (Volzhsky, Russia):

A. S. Zhukov, Director on Product Quality

Abstract

The type of metal stress-deformed state during pipe extrusion influences technological process parameters and hot extruded pipe quality. Existing experimental research methods do not determine stress and deformation areas in a deformation zone. So, the existing information about pipe extrusion is theoretic and speculative. During last years computer simulation methods was developed, in particular software based on the finite element method. This leads to the possibility to make analytical researches of stress-deformed state during steel pipe hot extrusion. Special attention during simulation is focused on deformation conditions in surface layers because common defect of hot extruded pipe surface is surface cracks and delamination. For potential surface cracks forecast it is necessary to estimate stress state, flow rate and temperature of metal. Therefore, information obtained by the computer simulation favours forecasting of pipe surface quality, metal quality and searching ways to reduce cracking. With this aim, numerical data, describing changes along the deformation zone, a deformation tenzor component, the level of accumulated deformation stress-strain concerning temperature and friction ratio, was approximated. Moreover, the computer simulation of stress-deformed state during extrusion allows estimating the adequacy of simulating metal flow during pipe extrusion.

keywords Extrusion, pipes, stress, deformation, temperature, friction ratio, stress state, finite element method.
References

1. Vydrin A. V., Kosmatskiy Ya. I., Khramkov E. V. Technology and equipment for manufacture of hot-extruded tubes. Chelyabinsk: Izd. Tsentr YuUrGU. 2015. 105 p.
2. Kosmatskiy Y. Ig., Khramkov E. V., Fokin N. V., Tikhonova M. A. Improvement of ways of pipes production by the combined processes. Applied and Fundamental Studies. 2013. Vol. 1. pp. 203–205.
3. RF Patent 143437. Kosmatskiy Ya. I., Vydrin A. V., Khramkov E. V. Equipment for manufacture of hollow shapes. 2014. Bulleten No. 20. Suggested 12.03.2014; published 20.07.2014.
4. Osadchiy V. Ya., Vavilin A. S., Zimovets V. G., Kolikov A. P. Technology and equipment of tube production. Moscow: Intermet Inzhiniring. 2007. 560 p.
5. Loginov Yu. N., Antonenko L. V. Research of the strain-stress state for the prevention of longitudinal splits formation in the extruded pipe. Tsvetnye metally. 2010. No. 5. pp. 119-122.

6. Kolmogorov V. L. Stresses, strains, destruction. Moscow: Metallurgiya. 1970. 229 p.
7. Bogatov A. A. Mechanical properties and models of metals destruction. Ekaterinburg: UGTU-UPI. 2002. 329 p.
8. Xue L., Wierzbicki T. Ductile fracture initiation and propagation modeling using damage plasticity theory. Engineering Fracture Mechanics. 2008. Vol. 75. P. 3276–3293.
9. Kolikov A. P., Romantsev B. A. Theory of metal processing. Moscow: Izd. dom MISiS. 2015. 451 p.
10. Matveev M. A. Evaluation of metal destruction possibility in hot plastic deformation using Cocroft – Latama criterion. Nauchno-tekhnicheskie vedomosti SpbPU. Estestvennye i inzherenye nauki. 2017. Vol. 23. No. 2. pp. 109–126.
11. Kosmatskiy Ya. I. Investigation of material of hot-extruded pipes with helical inner ribbing surface. Chernye metally. 2017. No. 6. pp. 62–67.
12. Loginov Yu. N. Extrusion as a method of intensive deformation of metals and alloys. Ekaterinburg: Izd. Uralskogo universiteta. 2016. 158 p.
13. Kolmogorov V. L., Shishmintsev V. F. Metal physics and metal science. Moscow: Metallurgiya. 1966. 960 p.
14. Vichuzhanin D. I., Shikhov S. E., Smirnov S. V., Churbaev R. V. Influence of stressed state on ultimate ductility of copper wire rod MOOK. Izvestiya vuzov. Tsvetnaya metallurgiya. 2015. No. 5. pp. 39–45.
15. Dukmasov V. G., Vydrin A. V. Mathematical models and rolling processes for high-quality shapes. Chelyabinsk: Izd. Tsentr YuUrGU. 2002. 214 p.
16. Duan X., Velay X., Sheppard T. Application of finite element method in the hot extrusion of aluminium alloys. Materials Science and Engineering: A. 2004. Vol. 369. No. 1-2. pp. 66–75.
17. Lin Chao, Ransing Rajesh S. An innovative extrusion die layout design approach for single-hole dies. Journal of Materials Processing Technology. 2009. Vol. 209. pp. 3416–3425.
18. Manegin Yu. V., Pritomanov A. E., Shpittel T., Knauschner A. Hot extrusion of tubes and shapes. Moscow: Metallurgiya. 1980. 272 p.

Language of full-text russian
Full content Buy
Back