Журналы →  Non-ferrous Мetals →  2018 →  №2 →  Назад

MATERIAL SCIENCE
Название Development of nickel-based filler metal for producing high-strength joints in critical products from heat-resistant materials
DOI 10.17580/nfm.2018.02.08
Автор Ivannikov A. A., Sevryukov O. N., Penyaz M. A., Popov N. S.
Информация об авторе

National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), Russia, Moscow:

A. A. Ivannikov, Senior Lecturer, Department №9 “Physical problems of materials science”, email: ivannikov7@rambler.ru
O. N. Sevryukov, Assistant Professor, Department №9 “Physical problems of materials science”, email: sevr54@mail.ru
M. A. Penyaz, Post-Graduate Student, Department №9 “Physical problems of materials science”
N. S. Popov, Graduate Student, Department №9 “Physical problems of materials science”

 

The article was attended by the staff of the Department №9 “Physical problems of materials science” NRNU MEPhI – Kalin B. A., Suchkov A. N., Fedotov I. V.

Реферат

Manufacturers of nozzles for liquid rocket engines from heat-resistant austenitic and austenitic-ferritic steels faced the problem of brittle boron nitride formation in the joints. Joints are obtained using hightemperature diffusion brazing in vacuum by filler metal based on Ni – Cr – Fe – Si – B system. This technology is based on the isothermal solidification of the filler metal melt, occurring due to the diffusion of boron into the base material. The developed boron-free nanocrystalline thin film filler metal Ni – 8Si – 5Nb wt.% was proposed to solve the brittle boron nitride problem. The melting interval 1103–1120 oC of the filler metal is determined by the method of differential thermal analysis. It’s structural and phase state was revealed by X-ray methods. Technological modes of high-temperature diffusion brazing of austenitic and austenitic-ferritic steels have been developed in the temperature range of 1150–1200 oС. The metallographic studies of the brazed joint were carried out. To determine the joint strength characteristics, the microhardness was investigated in the brazed zone and mechanical uniaxial tension tests were carried out according to GOST (Russian State Standard) 28830–90. The best result on the tensile strength 450±30 MPa was achieved on samples obtained at an isothermal holding temperature of 1150 oC for 30 min. As a result of this work, the possibility of using boron-free nanocrystalline thin film filler metal for brazing heat-resistant nitrogen-containing steels has been demonstrated. High-strength joints were obtained.

This work was supported by the MEPhI Academic Excellence Project.

Ключевые слова Joint, diffusion brazing, filler metal, rocket engine, nozzle, heat-resistant steel, nickel, boron
Библиографический список

1. Lashko S. V., Lashko N. F. Brazing metals. Moscow : Mashinostroenie, 1988. 376 p.
2. Ivannikov A. A., Tukhbatov V. A., Suchkov A. N., Ustyuzhaninov A. L., Bogachev I. A. Rapidly quenched nickel based filler metal for high temperature various constructive elements brazing. Tsvetnye Metally. 2014. No. 12. pp. 27–31.
3. Ivannikov A. et al. The use of Ni – Cr – Si – Be filler metals for brazing of stainless steels. IOP Conference Series: Materials Science and Engineering. 2016. Vol. 130, Conference 1. 130 012045.
4. Fedotov V. T., Suchkov A. N., Kalin B. A., Sevryukov O. N., Ivannikov A. A. Rapidly quenched filler metal STEMET for brazing of materials of modern technology. Tsvetnye Metally. 2014. No. 12. pp. 32–37.
5. Brazing. Reference book. Petrunin I. E. et al. Moscow : Mashinostroenie, 2003. 480 p.
6. Khorunov V. F. Basics of brazing of thin-walled structures from high-alloy steels. Kiev: Naukova Dumka, 2008. 238 p.
7. Zhu, W. et al. Microstructure and Ni – Cr – B – Si filler. Materials Science and Technology. 2018. Vol. 34, No. 8. pp. 926–933.
8. Logvenchev I.S. et al. The brazing of nickel alloys for nuclear reactor with the using of the rapidly-quenched filler metals. Inorganic Materials: Applied Research. 2014. Vol. 5, Issue 3. pp. 263–267.
9. Rabinkin A. High temperature brazing: filler metals and processing. Advances in brazing: Science, technology and applications. 2013. No. 1980. pp. 121–159.
10. Chen Y. et al. The Microstructural evolution of vacuum brazed 1Cr18Ni9Ti using various filler metals. Materials. 2017. Vol. 10, No. 4. p. 2018.
11. Lemus-Ruíz J. et al. Characterization, shear strength and corrosion resistance of aISI 304 using a Ni Fe – Cr – Si metallic glass foil. Journal of Materials Processing Technology. 2015. Vol. 223. pp. 16–21.
12. Lyakishev N. P., Bannykh O. A., Rokhlin L. L. State diagrams of double metallic systems : Reference book in 3 volumes. Moscow : Mashinostroenie, 1996. 1024 p.

Полный текст статьи Development of nickel-based filler metal for producing high-strength joints in critical products from heat-resistant materials
Назад