Журналы →  Tsvetnye Metally →  2017 →  №9 →  Назад

METAL PROCESSING
Название Research of rolling regimes and mechanical properties of cold-rolled, annealed and welded semi-finished products from experimental alloys of Al – Mg system, economically alloyed by scandium
DOI 10.17580/tsm.2017.09.13
Автор Baranov V. N., Sidelnikov S. B., Bezrukikh A. I., Zenkin E. Yu.
Информация об авторе

Siberian Federal University, Krasnoyarsk, Russia:

V. N. Baranov, Assistant Professor, Director of Institute of Non-Ferrous Metals and Materials Science
S. B. Sidelnikov, Professor, Head of a Chair “Metal Forming”, e-mail: sbs270359@yandex.ru
A. I. Bezrukikh, Assistant Professor of a Chair “Metal Forming”

 

JSC “RUSAL” Bratsk Aluminium Smelter, Bratsk, Russia:
E. Yu. Zenkin, Managing Director

Реферат

Our paper shows the research results of thermodeformation machining of flat ingots made of experimental aluminium alloys, containing magnesium, scandium, rare-earth and transition metals. Relevance of the work aimed at creating the new Al – Mg system alloys, alloyed by scandium, and technologies for obtaining deformed semi-finished products from them using metal forming operations are shown. Regimes of hot and cold sheet rolling for obtaining strips with thickness 1–3 mm from these alloys were calculated and experimentally tested. Experimental research included the following steps: preparation of flat slabs with dimensions 28150300 mm for rolling; hot rolling at the temperature of 450 оC with total draw ratio about 6; cold rolling with total draw ratio about 5; annealing of cold-deformed semi-finished products at the temperature of 350 оC within 3 hours; argon-arc welding of the obtained strips along and across the direction of deformation; intergranular corrosion test; evaluation of mechanical properties of the samples. As a result, the nature and degree of corrosion destruction were studied and mechanical properties of deformed, annealed and welded semi-finished products from experimental alloys were determined. It is established that they have a high level of strength and plastic properties of the metal along, across and at an angle 45o relative to the direction of rolling. So tensile strength reaches the value 500–520 MPa for deformed samples, yield strength of metal 435–470 MPa, relative elongation 4.8–6.7%, and for annealed samples the values of the relative elongation increase and can reach 14.0–14.5% at the sufficiently high yield strength 357–369 MPa. Tests for intergranular corrosion of samples after welding showed high corrosion resistance of welded joints. The strength of the welded seam is 0.75–0.85 of the strength of the base metal. The results of research can be recommended for the development of technology for the manufacture of parts from flat products, including welded joints.

Ключевые слова Aluminum alloys, scandium, zirconium, rolling, welding, intergranular corrosion, mechanical properties, force and moment of rolling
Библиографический список

1. Gorbunov Yu. A. The role and prospects of rare earth metals in the development of physical-mechanical characteristics and applications of deformable aluminum alloys. Zhurnal Sibirskogo federalnogo universiteta. Seriya: Tekhnika i tekhnologii. 2015. Vol. 8, No. 5. pp. 636–645.
2. Chunchang Shi, Liang Zhang, Guohua Wu, Xiaolong Zhang, Antao Chen, Jiashen Tao. Effects of Sc addition on the microstructure and mechanical properties of cast Al – 3Li – 1.5Cu – 0.15Zr alloy. Materials Science & Engineering: А. 2017. Vol. 680. pp. 232–238.
3. Pedro Henrique R. Pereira, Ying Chun Wang, Yi Huang, Terence G. Langdon. Influence of grain size on the flow properties of an Al – Mg – Sc alloy over seven orders of magnitude of strain rate. Materials Science & Engineering: A. 2017. Vol. 685. pp. 367–376.
4. Mondol S., Alamb T., Banerjee R., Kumar S., Chattopadhyay K. Development of a high temperature high strength Al alloy by addition of small amounts of Sc and Mg to 2219 alloy. Materials Science & Engineering: A. 2017. Vol. 687. pp. 221– 231.
5. Mengjia Li, Qinglin Pan, Yunjia Shi, Xue Sun, Hao Xiang. High strain rate superplasticity in an Al – Mg – Sc – Zr alloy processed via simple rolling. Materials Science & Engineering: A. 2017. Vol. 687. pp. 298–305.
6. Buranova Yu., Kulitskiy V., Peterlechner M., Mogucheva A., Kaibyshev R., Divinski S. V., Wilde G. Al3(Sc, Zr)-based precipitates in AleMg alloy: effect of severe deformation. Acta Materialia. 2017. Vol. 124. pp. 210–224.
7. Ibrokhimov S. Zh., Eshov B. B., Ganiev I. N., Ibrokhimov N. F. Influence scandium on the physicochemical properties of the alloy AMg4. Izvestiya Samarskogo nauchnogo tsentra Rossiyskoy akademii nauk. 2014. Vol. 16, No. 4.
pp. 256–260.
8. Ibrokhimov S. Zh., Eshov B. B., Ganiev I. N. The oxidation of solid Al – Mg alloy (AMg4) containing scandium. Doklady Akademii nauk Respubliki Tadzhikistan. 2013. Vol. 56, No. 6. pp. 472–475.
9. Kuznetsov G. M., Pobezhimov P. P., Nefedova L. P., Belov E. V. Peculiarities of formation of structure and properties of foundry Al – Mg alloys alloyed by scandium. Metallovedenie i termicheskaya obrabotka metallov. 1996. No. 6.
10. Drits M. E., Kadaner E. S., Dobatkina T. V., Turkina N. I. About the nature of scandium interaction with aluminium in aluminium-rich part of the system. Izvestiya AN SSSR. 1973. No. 4. pp. 213–217.
11. Sidelnikov S. B., Konstantinov I. L., Voroshilov D. S. Rolling technology : tutorial. Third edition. Krasnoyarsk : Sibirskiy federalnyy universitet, 2016. 180 p.
12. Yakivyuk O. V., Sidelnikov S. B., Dovzhenko N. N. et al. Investigation of mainainability of processing and properties of rolled materials from aluminium alloys of Al–Mg system, economically alloyed by scandium. Non-ferrous metals and minerals 2016 : collection of thesises of reports. Krasnoyarsk, 2016. pp. 262, 263.
13. Frolov V. A., Yakivyuk O. V., Frolov V. F., Voroshilov D. S. Properties of aluminium alloys, economically alloyed by scandium after deformation and thermal impact. Collection of materials of the XVII international scientific-technical ural school — seminar of metal scientists and young scientists. 2016. Part 2. pp. 113–117.
14. Frolov V. A. Investigation of mechanical properties of semiproducts from aluminium alloys, economically alloyed by scandium. Innovation processes of metal forming : materials of the 2 international scientific-practical conference. Ed.: M. V. Chukin. Magnitogorsk : Izdatelstvo Magnitogorskogo gosudarstvennogo tekhnicheskogo universiteta imeni G. I. Nosova, 2016. pp. 23, 24.
15. State Standard GOST 9.021–74. Unified system of corrosion and ageing protection. Aluminium and aluminium alloys. Accelerated test methods for intercrystalline corrosion. Introduced: 1975–01–01.
16. State Standard GOST 1778–70. Steel. Metallographic methods for the determination of nonmetallic inclusions. Introduced: 1972–01–01.
17. State Standard GOST 1497–84. Metals. Methods of tension test. Introduced: 1986–01–01.

Language of full-text русский
Полный текст статьи Получить
Назад