Journals →  Tsvetnye Metally →  2016 →  #4 →  Back

METAL PROCESSING
ArticleName Induction systems of precise heating of long-measured cylindrical billets made of titanium alloys
DOI 10.17580/tsm.2016.04.07
ArticleAuthor Demidovich V. B., Olenin V. A., Rastvorova I. I.
ArticleAuthorData

1 Saint Petersburg Electrotechnical University “LETI”, Saint Petersburg, Russia:

V. B. Demidovich, Professor, Senior Researcher of Inter-branch Laboratory “Modern Electrotechnologies”, e-mail: vbdemidovich@mail.ru
V. A. Olenin, Assistant of a Chair of Robotics and Industrial System Automation

 

National Mineral Resources University (Mining University), Saint Petersburg, Russia:
I. I. Rastvorova, Assistant Professor of a Chair of Electronic Systems

Abstract

Billets are called the long-measured, if their length is much bigger than the outside diameter of cylinders or the height or width of slabs. Peculiarity of precision heating of such billets is the necessity of creation of similar thermal conditions along length during the heating and transportation of the billets. These conditions are fulfilled, if each cross-section of the billet has the similar heating and heat losses from the beginning of heating to the beginning of plastic treatment. Various methods of electric heating of long-measured billets were discussed. Induction heating method is the most efficient and applicable. Induction heating of long-measured billets, making the reciprocal movements in several inductors, may become the alternative to the heating of the billets in one batch induction heater, where the movement of the billets along the guides is partially complicated because of the big mass or the length of the billet. The offered method shows that the billet is moving continuously, with periodical change of the movement direction on the opposite. The billet is heated in several inductors, placed along one axis. The rolls are placed between the inductors for the movement easing of the billet, which swings in the heating area of inductors with certain amplitude. Special software was developed for the joint calculation of electromagnetic and temperature fields, making possible the investigation and design of optimal constructions and control system of induction heater. The most important technological parameters (billet movement rate, current frequency, inductor power, etc) may be easy defined. There was also developed the method of assessment of technological accuracy of heating. Experimental measures have shown that maximal deflections of temperature by the billet volume are within 20 oС.

keywords Induction heating, precision heating, long-measured billets, titanium alloys, technological accuracy of heating, electromagnetic fields, temperature fields
References

1. Muehlbauer A. History of Induction Heating and Melting. Essen : Vulkan Verlag GmbH, 2008. 212 p.
2. Lozinskiy M. G. Promyshlennoe primenenie induktsionnogo nagreva (Industrial application of induction heating). Moscow : Publishing House of USSR Academy of Sciences, 1958. 470 p.
3. Slukhotskiy A. E., Ryskin S. E. Induktory dlya induktsionnogo nagreva (Inductors for induction heating). Leningrad : Energiya, 1974. 264 p.
4. Nemkov V. S., Demidovich V. B. Teoriya i raschet ustroystv induktsionnogo nagreva (Theory and calculation of induction heating equipment). Leningrad : Energoatomizdat, 1988. 271 p.
5. Aliferov A. I., Lupi S. Induktsionnyy i elektrokontaktnyy nagrev metallov (Induction and electromagnetic heating of metals). Novosibirsk : Publishing House of Novosibirsk State Technical University, 2011. 410 p.
6. Baake E., Joern K-U., Muehlbauer A. Energopotreblenie i emissiya CO2 pri promyshlennom tekhnologicheskom nagreve (Energiebedarf und CO2-Emissionen industrieller Prozesswärmeverfahren). Translated from German. Under the editorship of V. B. Demidovich. Essen : Vulkan-Verlag, 1997. 173 p.
7. Barankova I. I. Primenenie induktsionnogo nagreva dlya elektrotermicheskoy obrabotki izdeliy metiznoy otrasli (Application of induction heating for electromechanical treatment of metize industry products). Induktsionnyy nagrev = Induction heating. 2008. No. 2. pp. 30, 31.
8. Barankova I. I. Opredelenie effektivnogo elektricheskogo soprotivleniya buntov provoloki (Determination of efficient electric resistance of wire coils). Elektrichestvo = Electricity. 2010. No. 2. pp. 63–66.
9. Lucia O., Burdio J. M., Maussion P., Dede E. J. Induction heating technology and its applications: past developments, current technology, and future challenges. IEEE Transactions on Industrial Electronics. 2014. Vol. 61, No. 5. pp. 2509–2520.
10. Ilin A. A., Kolachev B. A., Polkin I. S. Titanovye splavy. Sostav, struktura, svoystva (Titanium alloys. Composition, structure, properties). Moscow : All-Russia Institute of Light Alloys – Moscow State Aviation Technological University, 2009. 520 p.
11. Demidovich V., Rastvorova I., Olenin V. Precise induction heating of Ti and Zr billets. Heat processing. 2011. No. 3. pp. 266–270.
12. Demidovich V. B., Olenin V. A., Chmilenko F. V. Sposob induktsionnogo nagreva dlinnomernykh izdeliy (Method of induction heating of long-measured products). Patent RF, No. 2333618. Applier and patent-holder: All-Russia Scientific-Research Institute of High-Frequency Currents named after V. P. Vologdin. Applied : November 20, 2006. Published : September 10, 2008. Bulletin No. 25.

Language of full-text russian
Full content Buy
Back