Journals →  Tsvetnye Metally →  2016 →  #1 →  Back

COMPOSITES AND MULTIPURPOSE COATINGS
ArticleName Impact of the functional coating on service durability of injection molds for the zinc alloys pressure casting
DOI 10.17580/tsm.2016.01.11
ArticleAuthor Gavariev R. V., Savin I. A., Leushin I. O.
ArticleAuthorData

Kazan National Research Technical University named after A. N. Tupolev — КAI, Kazan, Russia:

R. V. Gavariev, Senior Lecturer of a Chair “Design-Technological Supplying of Machine-Building Productions”, e-mail: Gavarievr@mail.ru
I. A. Savin, Assistant Professor, Head of a Chair “Design-Technological Supplying of Machine-Building Productions”


Nizhny Novgorod State Technical University, Nizhny Novgorod, Russia:
I. O. Leushin, Professor, Head of a Chair “Metallurgical Technologies and Equipment”

Abstract

The problem of service durability of the injection molds for zinc alloys pressure casting was examined. Differences between pressure casting of aluminum and zinc alloys are assigned. Key factors affecting damages of the shape-generating surfaces are considered, including the ones caused by power and temperature influences. It is determined that the greatest negative impact is caused by tensile stresses resulting in arising of new cracks and growth of already existing ones. It is indicated the need of making the additional compression stresses to compensate the tensile stresses impact. These conditions are met by the proposed method of the molds’ durability increase, based on the solid multifunctional coverings put by cathode-ion bombardment. The principal advantage of the above mentioned coverings is substantiated by the fact that the positive properties of the single layer are not changed when it is used in a multi-layer structure. There are also determined the key characteristics of nitration presenting the most common way of increasing the service durability of the shape-generating surfaces. The experimental data in support of the proposed theoretical hypothesis are cited. According to these data, the use of multilayer coating put by cathode-ion bombardment allows to increase the quality of the obtained castings in a porosity parameter. Moreover, the service durability indicator of the inserts with a multilayer coating is increased by 25% as compared with the nitration ones and makes about 200 000 cycles of press fittings.

keywords Injection mold, pressure casting, zinc alloys, multipurpose coverings, service durability, molybdenum
References

1. Denisov V. Yu. Vzaimodeystvie splavov alyuminiya s materialami press-form i povyshenie ikh stoykosti funktsionalnymi pokrytiyami : avtoreferat disssertatsii … kandidata tekhnicheskikh nauk (Interaction of aluminium alloys with mold materials and increasing of their resistivity by functional coatings : thesis of inauguration of Dissertation … of Candidate of Engineering Sciences). Tyumen, 2005. 16 p.
2. Fang H.-Z., Li R.-X., Chen R.-R., Yu B.-Y., Qu Y.-D., Xun S.-W., Li R.-D. Microstructure and mechanical properties of Al – 6Zn – 2.5Mg – 1.8Cu alloy prepared by squeeze casting and solid hot extrusion. Transactions of Nonferrous Metals Society of China. 2015. Vol. 25, No. 7. pp. 2130–2136.
3. Mo W., Zhang L., Wu G., Zhang Y., Liu W., Wang C. Effects of processing parameters on microstructure and mechanical properties of squeeze-cast Mg – 12Zn – 4Al – 0.5Ca alloy. Materials and Design. 2014. Vol. 63. pp. 729–737.
4. Gavariev R. V., Leushin I. O., Savin I. A. Problema prognozirovaniya ekspluatatsionnogo resursa press-form litya pod davleniem tsinkovykh splavov i nekotorye puti ee razresheniya (Problem of forecasting of service life of zinc alloy pressure die casting molds and some ways of its solving). Spravochnik. Inzhenernyy zhurnal = Handbook. An Engineering Journal. 2013. No. 6. pp. 26–29.
5. Belomyttsev M. Yu., Belyakov B. G., Krushinskiy Yu. Yu., Kotov A. N. Sposob azotirovaniya molibdenovykh vkladyshey press-form (Method of nitration of molybdene die liners). Certificate of Authority of USSR, No. 1560617, IPC С 23 С 8/24. Applied: March 01, 1988. Published: April 30, 1990. Bulletin No. 1.
6. Sobolnitskiy G. D., Kononov V. A., Tupchiy Yu. P., Sokolovskiy A. G., Smirnov Yu. N. Sposob polucheniya teplozashchitnogo pokrytiya na metallicheskoy forme dlya otlivki detaley iz alyuminievykh splavov (Method of obtaining of thermal-protection coating on metallic form for aluminium alloy detail casting). Certificate of Authority of USSR, No. 1678508, IPC В 22 С 23/02. Applied: December 25, 1989. Published: September 23, 1991. Byulletin No. 1.
7. Chen J., Wei J., Yan H., Su B., Pan X. Effects of cooling rate and pressure on microstructure and mechanical properties of sub-rapidly solidified Mg – Zn – Sn – Al – Ca alloy. Materials and Design. 2013. Vol. 45. pp. 300–307.
8. Ji S., Yan F., Fan Z. Development of a high strength Al – Mg2Si – Mg – Zn based alloy for high pressure die casting. Materials Science and Engineering: A. 2015. Vol. 626. pp. 165–174.
9. Goryunov I. I. Press-formy dlya litya pod davleniem (Pressure die casting molds). Leningrad : Mashinostroenie, 1974. 255 p.
10. Chikhranov A. V., Gataullov I. N. Sovershenstvovanie iznosostoykikh ionno-plazmennykh pokrytiy na osnove nitrida titana (Improvement of wearresistant ion-plasma coatings on the basis of titanium nitride). Novye materialy v mashinostroenii = New materials in mechanical engineering. 2011. No. 14. pp. 121–124.
11. Nozhenkov M. V. Struktura i svoystva kompozitsionnykh ionnoplazmennykh pokrytiy (Structure and properties of composite ion-plasma coatings). Trenie i smazka v mashinakh i mekhanizmakh = Friction and lubrication in machines and mechanisms. 2013. No. 6. pp. 3–12.
12. Savin I. A. Issledovanie kharakteristik iznosostoykikh pokrytiy, nanosimykh na rezhushchie instrumenty slozhnoy formy metodom katodno-ionnoy bombardirovki (Investigation of characteristics of wear-resistant coatings, sprayed on complex shape cutting instruments by method of cathode-ion bombardment). Zagotovitelnye proizvodstva v mashinostroenii = Blank productions in mechanical engineering. 2012. No. 9. pp. 41–44.
13. Goncharov M. V., Goncharov V. S. Ionno-plazmennye sloistye kompozitsionnye pokrytiya s osobymi svoystvami (Ion-plasma layer composite coatings with special properties). Nauka – promyshlennosti i servisu = Science – to industry and service. 2012. No. 6–3. pp. 69–76.
14. GOST 19424–97. Splavy tsinkovye liteynye v chushkakh. Tekhnicheskie usloviya (State Standard 19424–97. Cast zinc alloys in pigs. Specifications). Introduced: 2001–07–01. (in Russian).
15. Sobol O. V. Ob upravlenii strukturnoy i napryazhennym sostoyaniem tonkikh plenok i pokrytiy v protsesse ikh polucheniya ionno-plazmennymi metodami (About the control of structural and stressed state of fine films and coatings in the process of their obtaining by ion-plasma methods). Fizika tverdogo tela = Physics of the Solid State. 2011. Vol. 53, No. 7. pp. 1389–1398.

Language of full-text russian
Full content Buy
Back