Journals →  Tsvetnye Metally →  2015 →  #10 →  Back

METAL PROCESSING
ArticleName Influence of thermomechanical treatment on electrical resistivity and hardening of alloys Al – 0.2% Zr and Al – 0.4% Zr
DOI 10.17580/tsm.2015.10.02
ArticleAuthor Belov N. A., Korotkova N. O., Dostaeva A. M., Akopyan T. K.
ArticleAuthorData

National University of Science and Technology “MISiS”, Moscow, Russia:

N. A. Belov, Professor, Director of Engineering Center “Casting Technologies and Materials”, e-mail: nikolay-belov@yandex.ru
N. O. Korotkova, Post-Graduate Student of Casting Process Technology Chair
Т. K. Akopyan, Researcher of Engineering Center “Casting Technologies and Materials”

 

Kazakh National Technical University named after K. Satpaev, Almaty, Kazakhstan:

A. M. Dostaeva, Doctoral Student of a Chair of Machine-Tool Construction, Material Science and Mechanical Facilities Technology

Abstract

In the last years, power engineering has been stably interested in aluminium alloys, having high electroconductivity and sufficient durability, remaining after heating up to the temperature of 250–300 °С. Traditional wires, made of technical aluminium А5Е and А7Е, do not fulfill theese requirements because of their strong softening even after short-time heating to such temperatures. Creation of wire, made of low aluminium alloy with zirconium addition, is the most prospective way of this problem solving. The increased high-temperature durability of these alloys is provided due to the secondary isolations of Al3Zr phase, which sizes are ~10 nm. The electrical resistivity of aluminiunm is significantly increased by zirconium in aluminium solid solution. According to this, annealing is required for maximal decrease of Zr concentration in aluminium solid solution, and, on the other hand — for the formation of the required amount of Al3Zr phase nanoparticles. There was researched the influence of thermomechanical treatment modes on specific electrical resistivity and hardness of two aluminium alloys (cold rolled and hot rolled ignots and sheets, containing 0.2 and 0.4% Zr). There was made a definition that the slowest decomposition of solid Al solution is in ignots, and the fastest one is in cold-rolled sheets. Desirability function application shows that the best combination of values of specific electrical resistivity, hardness and softening resistance can be reached in cold-rolled sheets, made of alloy 0.4% Zr, annealed at the temperature of 450 °C. This combination of properties is mainly substantiated by formation of a sufficient number of Al3Zr phase nanoparticles, which define the strain hardening saving.
This article was written in the context of the Agreement No. 14.578.21.0039 (unique identifier of the project is RFMEFI57814X0039) for the subsidy of Ministry of Education and Science of Russian Federation in the context of the Federal Target Program “Research and development of priority ways of development of scientific-technological complex of Russia for 2014–2020”.

keywords Alloys, electrical resistivity, thermomechanical treatment, hardening, softening, aluminum, zirconium
References

1. Belyy D. I. Alyuminievye splavy dlya tokoprovodyashchikh zhil kabelnykh izdeliy (Aluminium alloys for electric conductors of cables). Kabeli i Provoda = Cables and Wires. 2012. No. 1. pp. 8–15.
2. Peshkov I. B. Sostoyanie i perspektivy primeneniya alyuminiya v kabelnoy promyshlennosti (State and prospects of aluminium application in cable industry). Kabeli i Provoda = Cables and Wires. 2009. No. 1. pp. 7–9.
3. Uliasz P., Knych T., Mamala A., Smyrak B. Aluminium Alloys. Edited by J. Hirsch, B. Skrotzki, G. Gottstein. Weinheim : WILEY-VCH, 2008. pp. 248–255.
4. Prokhorov A. Yu. Issledovanie i razrabotka tekhnologii plavki i litya termostoykogo alyuminievogo splava s dobavkoy tsirkoniya s tselyu polucheniya slitkov dlya elektrotekhnicheskogo primeneniya : dissertatsiya … kandidata tekhnicheskikh nauk (Research and development of technology of fusion and casting of heat-resistant aluminium alloy with addition of zirconium for the purpose of ingot obtaining for electrotechnical application : Dissertation … of Candidate of Engineering Sciences). Moscow : MISiS, 2011.
5. Dostaeva A. M. Obosnovanie sostava i rezhima termoobrabotki provodnikovykh Al–Zr splavov, poluchaemykh v vide katanki : dissertatsiya … doktora filosofii (Substantiation of composition and mode of thermal treatment of conduction Al–Zr alloys, obtained in the rod type : Dissertation … of PhD). Almaty : Kazakh National Technical University, 2015.
6. Belov N. A., Alabin A. N., Prokhorov A. Yu., Skvortsov N. V. Vliyanie promezhutochnogo otzhiga na elektrosoprotivlenie provoloki nizkolegirovannykh alyuminievykh splavov sistemy Al–Zr–Fe–Si (Influence of intermediate annealing on electrical resistvity of wire of low aluminium alloys of Al–Zr–Fe–Si system). Metallovedenie i termicheskaya obrabotka metallov = Metal Science and Heat Treatment. 2012. No. 4. pp. 14–19.
7. Lefebvre W., Danoix F., Hallem H., Forbord B., Bostel A., Marthinsen K. Precipitation kinetic of Al3(Sc, Zr) dispersoids in aluminium. Journal of Alloys and Compounds. 2009. Vol. 470. pp. 107–110.
8. Knipling K. E., Dunand D. C., Seidman D. N. Precipitation evolution in Al–Zr and Al–Zr–Ti alloys during isothermal aging at 375–425 °C. Acta Materialia. 2008. Vol. 56. pp. 114–127.
9. Clouet E., Barbu A., Lae L., Martin G. Precipitation kinetics of Al3Zr and Al3Sc in aluminum alloys modeled with cluster dynamics. Acta Materialia. 2005. Vol. 53. pp. 2313–2325.
10. GOST 11069–2001. Alyuminiy pervichnyy. Marki (State Standard 11069-2001. Primary aluminium. Grades). Introduced : January 01, 2003. (in Russian)
11. GOST 53777–2010. Ligatury alyuminievye. Tekhnicheskie usloviya (State Standard 53777–2010. Master alloys of aluminium. Specifications). Introduced : July 01, 2010. (in Russian).
12. Belov N. A. Fazovyy sostav promyshlennykh i perspektivnykh alyuminievykh splavov (Phase composition of industrial and prospective aluminium alloys). Moscow : MISiS, 2010. 511 p.
13. Mondolfo L. F. Struktura i svoystva alyuminievykh splavov (Structure and properties of aluminium alloys). Moscow : Metallurgiya, 1979. 640 p.
14. Sigli C. Zirconium Solubility in Aluminum Alloys [C]. Proceedings of International conference on aluminium alloys ICAA9. Brisbane (Australia), 2004. pp. 1353–1358.
15. Novik F. S., Arsov Ya. B. Optimizatsiya protsessov tekhnologii metallov metodami planirovaniya eksperimentov (Optimization of metal technology processes by experiment planning methods). Moscow : Mashinostroenie, 1980. pp. 26–32.

Language of full-text russian
Full content Buy
Back