Journals →  Tsvetnye Metally →  2014 →  #11 →  Back

METAL PROCESSING
ArticleName Influence of liquid hot isostatic pressing on structure and properties of new lean alloyed high strength casting aluminum alloy Al6Zn0.5Ni (АЦ6Н0,5Ж) on the basis of Al – Zn – Mg – Ni – Fe system
ArticleAuthor Akopyan T. K., Belov N. A., Kaybyshev R. O., Alabin A. N.
ArticleAuthorData

A. A. Baikov Institute of Metallurgy and Materials Science of Russian Academy of Sciences, Moscow, Russia:

T. K. Akopyan, Acting Junior Researcher, e-mail: aktorgom@gmail.com

 

National University of Science and Technology “MISiS”, Moscow, Russia:

N. A. Belov, Professor, Director of Engineering Center “Innovation Casting Technologies and Materials”

A. N. Alabin, Head of Department of Engineering Center “Innovation Casting Technologies and Materials”


Belgorod State National Research University, Belgorod, Russia:
R. O. Kaybyshev, Head of Laboratory of Mechanical Properties of Nanostructure and Heat-Resistance Materials

Abstract

Barothermal treatment by liquid hot isostatic pressing (LHIP) was used for casts of new lean alloyed high strength casting aluminum alloy Al6Zn0.5Ni (АЦ6Н0,5Ж) (on the basis of Al – Zn – Mg – Ni – Fe system) for two modes with different isothermal exposure temperature: t1 = 490 oC (LHIP1) and t1 = 510 oC (LHIP2). The alloy was melted in laboratory resistance electric furnace in graphite-chamotte crucible. Casting was carried out into steel mold. Microstructure of casting and heat-treated samples was studied with an Axio Observer MAT optical microscope and JSM-6610LV scanning electron microscope. Microstructure of the alloy after heat treatment without LHIP contains large irregularly shaped shrinkage pores with an average size of 10–60 μm. Results show that 2 minutes of LHIP at the pressure of 120 MPa lead to significant removing of porosity. LHIP eliminates shrinkage porosity, which highly improves mechanical properties. LHIP and heat treatment on the T6 regime provides increase of UTS by 20%, fracture elongation by 6 times and fatigue strength by 1.5 times. Results show the possibility of achieving of high mechanical properties of aluminum castings, which allows their use to replace the commercial high-strength casting alloys of Al – Cu system (particularly AM5).

keywords High strength casting aluminum alloys, liquid hot isostatic pressing, Al – Zn – Mg – Ni – Fe system, eutectic, mechanical properties, microstructure
References

1. Polmear I. J. Light Metals : From Traditional Alloys to Nanocrystals. 4th edition. Oxford : Elsevier, 2006. 421 p.
2. Zolotorevskiy V. S., Belov N. A. Metallovedenie liteynykh alyuminievykh splavov (Physical metallurgy of casting aluminium alloys). Moscow : MISiS, 2005. 376 p.
3. Belov N. A. Fazovyy sostav promyshlennykh i perspektivnykh alyuminievykh splavov (Phase composition of industrial and prospective aluminium alloys). Moscow : Publishing House “MISiS”, 2010. 511 p.
4. Belov N. A. Ekonomnolegirovannye vysokoprochnye alyuminievye splavy: printsipy optimizatsii fazovogo sostava (Lean alloyed highstrength aluminium alloys: principles of optimization of phase composition). Metallovedenie i termicheskaya obrabotka metallov = Metal Science and Heat Treatment. 2011. No. 9. pp. 19–27.
5. Belov N. A., Belov V. D., Alabin A. I., Zlobin G. S., Mishurov S. S. Vysokoprochnyy ekonomnolegirovannyy splav na osnove allyuminiya (High-strength lean alloyed aluminium-based alloy). Patent RF, No. 2484168. Applied: February 21, 2012. Published: June 10, 2013. Bulletin No. 16.
6. Akopyan T. K., Belov N. A., Alabin A. N., Zlobin G. S. Calculation-Experimental Study of the Phase Composition of Al – Zn – Mg – (Cu) – Ni – Fe Aluminum Alloys. Russian Metallurgy (Metally). 2013. Vol. 2013, No. 7. pp. 545–552.

7. Akopyan T. K., Belov N. A., Alabin A. N., Zlobin G. S. Raschetnoeksperimentalnoe issledovanie stareniya liteynykh vysokoprochnykh alyuminievykh splavov sistemy Al – Zn – Mg – (Cu) – Ni – Fe (Calculation-experimental research of aging of casting high-strength aluminium alloys of Al – Zn – Mg – (Cu) – Ni – Fe system). Metally = Metals. 2014. No. 1. pp. 70–76.
8. Stroganov G. B. Vysokoprochnye liteynye alyuminievye splavy (Highstrength casting aluminium alloys). Moscow : Metallurgiya, 1985. 216 p.
9. Islam Md. A., Farhat Z. N. The influence of porosity and hot isostatic pressing treatment on wear characteristics of cast and P/M aluminum alloy. Wear. 2011. Vol. 271, Iss. 9. pp. 1594–1601.
10. Ceschini L., Morri A., Sambogna G. The effect of hot isostatic pressing on the fatigue behavior of sand-cast A356-T6 and A204-T6 aluminum alloys. Journal of Materials Processing Technology. 2008. Vol. 204, Iss. 1. pp. 231–238.
11. Petrov P., Konstantinova S., Buchvarov G., Petrov I. Hot isostatic pressing treatment of AlSi7Mg aluminium alloy. Journal of Materials Processing Technology. 1994. Nо. 2. pp. 26–33.
12. Romano E., Rosso M., Mus C. The effect of liquid hot isostatic pressing on fatigue properties of Al based castings. Metallurgical Science and Technology. 2001. Vol. 19, No. 1. pp. 21–27.
13. Chandley D. Origin of the liquid hot isostatic pressing process. Metallurgical Science and Technology. 2001. Vol. 19, No. 1. pp. 3–5.
14. Ivanova E. V., Tagirov D. V., Kaybyshev R. O. Vliyanie zhidkofaznogo goryachego izostaticheskogo pressovaniya na svoystva litykh alyuminievykh splavov. Chast 1. Struktura i svoystva splava AK7ch, poluchennogo litem v peschanye formy (Influence of liquid-phase hot isostatic pressing on properties of casting aluminium alloys. Part 1. Structure and properties of alloy AK7ch (АК7ч), obtained by casting in sand forms). Metallovedenie i termicheskaya obrabotka metallov = Metal Science and Heat Treatment. 2012. No. 2. pp. 11–17.
15. Tagirov D. V., Ivanova E. V., Kaybyshev R. O. Vliyanie zhidkofaznogo goryachego izostaticheskogo pressovaniya na svoystva liteynykh alyuminievykh splavov. Chast 2. Struktura i svoystva splava AA356.02, poluchennogo litem v peschanye formy po tekhnologii Disamatic (Influence of liquid-phase hot isostatic pressing on properties of casting aluminium alloys. Part 2. Structure and properties of alloy AA356.02, obtained by casting in sand forms by Disamatic technology). Metallovedenie i termicheskaya obrabotka metallov = Metal Science and Heat Treatment. 2012. No. 2. pp. 18–23.
16. GOST 1583–93. Splavy alyuminievye liteynye. Tekhnicheskie usloviya (State Standard 1583–93. Aluminium casting alloys. Technical conditions). Introduced: January 01, 1997. (in Russian).
17. GOST 10145–81. Metally. Metod ispytaniya na dlitelnuyu prochnost (State Standard 10145–81. Metals. Strength test method). Introduced: 1982-07-01. (in Russian).
18. GOST 1497–84. Metally. Metody ispytaniy na rastyazhenie (State Standard 1497–84. Metals. Tensile test methods). Introduced: January 01, 1986. (in Russian).
19. GOST 25.502–79. Raschety i ispytaniya na prochnost v mashinostroenii. Metody mekhanicheskikh ispytaniy metallov. Metody ispytaniy na ustalost (State Standard 25.502–79. Calculations and strength tests in mechanical engineering. Methods of mechanical tests of metals. Fatigue test methods). Introduced: January 01, 1981. (in Russian).

Language of full-text russian
Full content Buy
Back