Journals →  Tsvetnye Metally →  2013 →  #1 →  Back

COMPOZITES AND MULTIPURPOZE COATINGS
ArticleName Influence of the structure of diamond drill bits matrices on their abrasion resistance. Part 1. Properties of matrices of diamond drill bits
ArticleAuthor Polushin N. I., Laptev A. I., Baragunov E. M.
ArticleAuthorData

National University of Science and Technology “MISIS”, Moscow, Russia

N. I. Polushin, Head of the Scientific and Research Laboratory “Superhard materials”
A. I. Laptev, Leading Researcher, Scientific and Research Laboratory “Superhard materials”, e-mail: laptev@misis.ru
E. M. Baragunov, Student

Abstract

There were studied the microstructure and mechanical properties of 4 matrices of a complex chemical composition: WC – Co – Fe – Cu, WC – Сo – Fe – Cu – Ni, WC – Cu + cast tungsten carbide (melted and crushed WC), and WC – Cu – Ni + cast tungsten carbide. These matrices are applied at the manufacturing of geological prospecting diamond drill bits. The manufacturing process of matrices' samples was carried out, using the infiltration method, under the conditions of production of diamond drill bits at the temperature of 1150 oС, within 15 min. The sides of diamond free bits were obtained, holding their metallographic analysis, X-ray phase analysis and X-ray microanalysis. The hardness, microhardness, density and porosity of the slides were defined. The hardness of matrices was determined by the HRC scale. Using the load of 2 N, the microhardness of matrices was defined on the PMT-3 apparatus. During the working process, it has been established that, using an infiltration method, the dense matrices of the diamond tool with no more than 1 % of open porosity are obtained from the copper and cobalt-based melts of pressings from the particles of WC and particles of WC + cast tungsten carbide. The most hard matrices are the fine-grained WC-based matrices, infiltrated with an alloy of complex structure of Co – Fe – Cu – Ni. The introduction of nickel increases the hardness of the diamond tool matrices at the expense of increasing of durability of the copper-based alloys. The structure of matrices has no influence on the hardness of cast tungsten carbide particles. At the same time, the introduction of cast tungsten carbide particles doesn't lead to the substantial increasing of the general hardness of matrices.

keywords Matrix, diamond tool, drill bit, microstructure, density, hardness, porosity, infiltration
References

1. Tsypin N. V. Iznosostoykost kompozitsionnykh almazo soderzhashchikh materialov dlya burovogo instrumenta (Wear resistance of composite diamond containing materials for drilling tools). Kiev : Naukova dumka, 1983. 192 p.
2. Bugakov V. I., Elyutin A. V., Karavaev K. M., Laptev A. I., Polushin N. I. Izvestiya vuzov. Tsvetnaya metallurgiya — Russian Journal of Non-Ferrous Metals. 1998. No. 4. pp. 54–57.
3. Bugakov V. I., Elyutin A. V., Karavaev K. M., Laptev A. I., Polushin N. I. Novyy tip svyazok na osnove nikelya, legirovannogo diboridami titana i khroma, dlya almaznogo kamnerazrushayushchego instrumenta (New type of bindings on the basis of nickel, alloyed with titanium and chromium diborides, used for the diamond saxifragant tools). Izvestiya vuzov. Tsvetnaya metallurgiya — Russian Journal of Non-Ferrous Metals. 1998. No. 5. pp. 61–68.
4. Bugakov V. I., Elyutin A. V., Laptev A. I., Pozdnyakov A. A., Polushin N. I. Materialovedenie — Materials Science. 2003. No. 12. pp. 48–52.
5. Bugakov V. I., Laptev A. I., Polushin N. I., Bocharov M. V., Sorokin M. N. Materialovedenie — Materials Science. 2004. No. 2. pp. 24–28.
6. Bugaev A. A. Issledovanie i razrabotka koronok, impregnirovannykh sinteticheskimi almazami, i effektivnosti ikh primeneniya pri burenii geologorazvedochnykh skvazhin : dissertatsiya ... kandidata tekhnicheskikh nauk (Research and development of bits, infiltrated with synthetic diamonds, and their usage efficiency with the drilling of geological prospecting wells : Dissertation. … of Candidate of Engineering Sciences). Moscow, 1970.
7. Bugakov V. I., Laptev A. I., Pozdnyakov A. A. Izvestiya vuzov. Tsvetnaya metallurgiya — Russian Journal of Non-Ferrous Metals. 2005. No. 6. pp. 69–72.
8. Bondarenko N. A., Zhukovskiy A. N., Mechnik V. A. Osnovy sozdaniya almazosoderzhashchikh kompozitsionnykh materialov dlya porodorazrushayushchikh instrumentov (Creation basis of diamond containing composite materials for rock destroying tools). Kiev : V. Bakul Institute for Superhard Materials of the National Academy of Sciences of Ukraine, 2008. 456 p.
9. Budyukov Yu. E., Vlasyuk V. I., Spirin V. I. Almaznyy instrument dlya bureniya napravlennykh i mnogostvolnykh skvazhin (Diamond drilling tool for directionally drilled and multilateral wells). Tula : Grif and K, 2007. 176 p.
10. Osnovy proektirovaniya i tekhnologiya izgotovleniya abrazivnogo i almaznogo instrumenta (Basis of projecting and manufacturing technology of abrasive and diamond tools). Under the editorship of V. N. Bakul. Moscow : Mashinostroenie, 1975. 296 p.

Language of full-text russian
Full content Buy
Back